Morse Code Translator
Turn words into dots and dashes or read a message someone sent you, then hear it played or watch it flash.
The translator could not load. Refresh the page to try again.
Letter by letter
Morse code chart
Select any character to hear how it sounds, at the speed and pitch you've set above.
Letters
Numbers
Punctuation
How Morse timing works
Everything is measured in dits, the length of one dot. Get these ratios right and your Morse will sound correct at any speed, whether you're using a torch, a whistle or a radio.
| Signal | Length |
|---|---|
| Dot (dit) | 1 unit |
| Dash (dah) | 3 units |
| Gap inside a letter | 1 unit |
| Gap between letters | 3 units |
| Gap between words | 7 units |
Speed is given in words per minute, using the word PARIS as the yardstick, because it takes exactly 50 units including its word gap. To find the length of a dot in milliseconds, divide 1,200 by the speed. At 20 WPM, each dot lasts 60 ms.
Patterns that make it easier
The chart looks random until you notice how the letters pair up.
The commonest letters are the shortest
E is one dot and T is one dash. The designers gave frequent English letters the quickest codes, which saved operators a lot of tapping.
Many letters are opposites
Swap dots and dashes and you get another letter. A .- becomes N -., K -.- becomes R .-., and S ... becomes O ---.
Numbers follow one rule
Every digit has five symbols. 1 to 5 start with that many dots, so 3 is ...--. 6 to 9 start with dashes, so 7 is --..., and 0 is all dashes.
How to learn Morse code
The most common advice from people who use it is to learn by ear from day one. If you memorise a chart of dots and dashes, you end up translating each sound into a picture and then into a letter, and that extra step limits your speed.
Say it out loud
Dots are "dit" and dashes are "dah", so A is "di-dah". A dit at the end of a letter keeps its full sound, so R is "di-dah-dit".
Start with two letters
The Koch method has you listen at close to full speed with only two letters, then add another each time you're getting about 90% right.
Keep the letters fast and the gaps long
Farnsworth timing sends each letter at a higher speed but stretches the gaps between them, so you learn the sound of the whole letter and not a count of dots.
Practise little and often
Ten minutes a day tends to work better than an hour at the weekend. The chart above is handy for a quick session on your phone.
Why SOS is three dots, three dashes, three dots
SOS doesn't stand for anything. "Save Our Souls" came later. It was picked because the pattern is easy to send and hard to mistake for anything else, and it became the international distress signal under a 1906 treaty that took effect in 1908.
Strictly speaking, it isn't three letters. Operators send it as one unbroken signal, ...---..., with no letter gaps. This translator reads that form as SOS too.
Is anyone still using Morse code?
Samuel Morse and Alfred Vail developed the system for the telegraph, and Morse sent the famous message "What hath God wrought" from Washington to Baltimore in 1844. Commercial shipping dropped it as its main distress system in 1999.
It's still around, though. Amateur radio operators use it because a simple signal can get through when voice can't, aviation radio beacons identify themselves with it, and some people with limited movement use it to type with one or two switches.
Practice messages
Try these on paper with the chart, then check your answer.
.... . .-.. .-.. ---
--. --- --- -.. / .-.. ..- -.-. -.-
- .... .- -. -.- ...
When a translation comes out wrong
Everything joins into one strange letter
Letters need a space between them. .- followed by -... is AB, but .--... has no match at all. Unknown codes show as � so you can find the spot.
All the words run together
Words need a bigger break. Use a slash, a line break or three spaces, and this translator will treat any of them as a word gap.
Some characters disappear
International Morse covers the Latin alphabet, digits and common punctuation. Accented letters and scripts such as Hindi aren't included, so the tool tells you what it had to leave out.
Your text comes back in capitals
Morse has no upper or lower case, so there's no way to tell them apart. The result is always shown in capitals.
Common questions
What does the slash mean?
It marks a gap between words when Morse is written down. It isn't sent as a signal, and it's different from the slash character, which has its own code.
What speed should I use?
Around 15 WPM is a comfortable place to start listening. Below about 10 WPM, the rhythm of each letter starts to break apart and gets harder to recognise.
Why can't I hear anything?
Check that Sound on is ticked and your device isn't muted. On iPhones, the ring switch can silence web audio too. The lamp still flashes with the sound off.
What can I do with the downloaded audio?
It's a standard WAV file you can play anywhere or add to a video. Your message, speed and pitch are built into the file on your own device.
Is my message sent anywhere?
No. Translation and audio both happen in your browser, so nothing you type reaches our server.